Feature

Price a lane against what it actually costs you

Quoting built on a real all-in cost model, with a configurable rate floor applied consistently wherever rates are judged.

30-day free trial on up to 2 trucks. No card needed to start. Add one before day 30 to keep going.

That $2.50-a-mile load really pays

$2.00/mionce 20% of the miles are empty

Every lane shows two rates side by side — what it quotes per loaded mile, and what it earns across every mile the truck drove.

Worked example: $2.50 × (1 − 0.2)

Quoted rate per loaded mile
$2.50/mi
Share of the trip driven empty
20%

An example from the numbers shown — yours depend on your lanes, rates and fleet.

The problem

Rates get quoted on instinct, and nobody knows which lanes are actually losing money.

What changes

What Tezify does

A cost model that includes what the truck really costs to run, and one rate floor that every screen respects.

Your own rate history, lane by lane

Search a lane by origin and destination, by city or by state, and Tezify gathers every load you have run on it. You see how many loads that is, the average, median, lowest and highest rate, the rate on the most recent load, and the rate per loaded mile, weighted by miles so one short run cannot skew it.

The same lane is broken down month by month and by customer, so you can see whether a lane has been paying less lately and which shipper or broker it pays best with.

Empty miles are averaged only over the loads where someone recorded them, and the page shows how many loads that is. A load nobody entered deadhead for is not counted as a run with no empty miles, because that would make the lane look better than it is.

A quote built from what the lane has paid you

The suggested rate starts from the lane's own rate per mile, either across all your loads on it or across the most recent third of them if you want the current trend. You adjust it by a fuel percentage and a margin percentage, and Tezify applies it to the miles you are quoting.

Beside the suggestion you see the lowest and highest rate per mile the lane actually paid, projected onto the same miles, so the quote sits inside a range your own loads produced rather than a range someone else estimated.

What the truck costs to run, and the floor under every rate

The cost model takes your overhead, insurance, truck and trailer payments, the miles each truck runs a month, fuel, maintenance and driver pay per mile, and the dispatch and factoring percentages taken off revenue. From those it works out what a mile costs you.

Break-even per mile is that cost divided by what is left of a dollar of revenue after the dispatch and factoring percentages, so fees taken off the top are covered. The suggested rate lifts break-even by your target margin, counted as a share of revenue: a 20% target gives a rate where 20% of it is margin.

You can also set a dollar-per-mile rate floor. The load board matcher marks any posting below it as a blocker and shows the rate it worked out. If no floor is set, the matcher says the rate was not scored rather than assuming one.

Common questions

Does Tezify tell me the market rate for a lane?

Only through your own DAT account. With a DAT RateView login saved, the Quoting screen has a Check DAT market rate button that asks DAT about the lane and labels the answer with DAT and the time it was checked. Without one, rate analytics uses only the loads you have run and the cost model you enter, and never substitutes an outside figure for your own numbers.

How is break-even per mile worked out?

Your cost per mile — overhead, insurance and truck and trailer payments spread over the miles each truck runs, plus fuel, maintenance and driver pay per mile — divided by what is left of each revenue dollar after the dispatch and factoring percentages.

What happens if I have no rate floor set?

The load board matcher does not score the rate at all and says so on each match, rather than assuming a floor you did not choose.

See it on your own loads

Run your real loads through it before you decide anything.

Create your account
Free trial
30 days on up to 2 trucks, card needed
After that
From $49 a month, never per seat
Included
Every module, on every plan