Feature
A driver app for trucking companies, included for every driver
Android and iOS driver app for trucking companies: loads, directions, BOL and POD photos, inspections, pay and messages. No charge per driver.
30-day free trial on up to 2 trucks. No card needed to start. Add one before day 30 to keep going.
Saving 200 texted paperwork photos a week to the right load, a minute each, is
3 h 20 mina week
Drivers snap the BOL and POD in the app and the document lands on the load it belongs to.
Worked example: 20 × 5 × 2 × 1 min
- Drivers
- 20 drivers
- Loads per driver a week
- 5 loads
- Photos per load
- 2 (BOL and POD)
- Minutes to file one by hand
- 1 min
An example from the numbers shown — yours depend on your lanes, rates and fleet.
The problem
Drivers call dispatch to ask where they are going, then paperwork arrives a week late and half of it is unreadable.
What changes
What Tezify does
The load, the stops, the directions and the documents in the driver's hand, with scan-quality checks so a POD is legible the first time.
- Native Android and iOS, included on every plan for every driver
- BOL and POD photo capture, with an AI review (when enabled) that flags an unreadable or altered page to the office
- Pre-trip and post-trip inspections with photos and signature
- Document wallet for CDL, medical card and insurance with expiry reminders
- Rates, margins and dispatcher documents never reach the device
Who the driver app is for
It is for company drivers and leased owner-operators hauling for a carrier that runs on Tezify. The office assigns the load and the driver works it from the phone. The driver buys nothing and installs nothing else.
Each driver signs in with a driver code from the office and a PIN of 4 to 8 digits, which they can change in the app. There is no email account to set up, so adding a new driver takes a minute.
The load, answered from the cab
When a load is assigned, the driver accepts it or declines it with a reason, right in the app. The answer is recorded on the load, and a decline notifies dispatch straight away with the driver's reason, so the load can be covered again before the pickup window rather than after it.
The driver opens a rate confirmation generated for their own load at the carrier rate you set, never the broker's original. A driver can only open loads assigned to them.
Paperwork and inspections that arrive the same day
From the load, the driver updates its status, photographs the bill of lading and proof of delivery, completes a pre-trip or post-trip inspection, and reports an issue or an accident. Each one lands on the load in the office as it happens, rather than in a stack of paper at the end of the week.
If a submission seems to fail in a dead zone and the driver taps submit again, the same inspection is not logged twice. If they retake a blurry photo, the new photos are kept rather than mistaken for a repeat.
With AI turned on, each uploaded photo is reviewed for what a safety manager would flag, such as visible damage, an unsecured load, a leak, or paperwork that looks altered or unreadable, and a serious finding goes to the safety feed with the photo.
Pay the driver can see, and question
The pay tab shows an estimate of what each current load pays the driver and what delivered loads have earned. It is labelled as an estimate, because the settlement is what actually pays. Cancelled loads are left out, because they were never earned.
If a figure looks wrong, the driver raises a pay question from the app instead of calling. It reaches the office as a record, and when someone closes it the driver is notified with the answer.
The driver also sets their duty status (driving, on duty, sleeper or off duty), so dispatch can see who is available.
Everything else the driver needs, in the same app
Messages with the office live in the app's inbox. The driver sees their hours of service from the ELD when one is connected (otherwise an estimate from the duty status they set, labelled as one), and a detention timer logs the wait at the dock while it happens.
Fuel and receipts are logged for IFTA with a photo of the receipt. Nearby fuel prices come from the truck's own position, each shown with when it was last updated. Time off is requested from the app, the driver's safety score is on its own screen, and a step-by-step accident guide walks them through photos and the other party's details.
Tezify AI answers the driver's own questions about their hours, loads and pay, and how to send a BOL. It reads and advises; it changes nothing.
A driver's day in the app
- 1
Sign in
Driver code and PIN. The app opens on the loads assigned to that driver and nothing else.
- 2
Accept the load
Accept it, or decline with a reason that goes straight to dispatch.
- 3
Pre-trip inspection
Walk the truck with the inspection form, add photos of anything wrong, and sign it.
- 4
Run the stops
Stops and directions are on the load. Duty status is set from the app, and the detention timer logs the wait at the dock.
- 5
Send the paperwork
Photograph the BOL at pickup and the POD at delivery. Both land on the load in the office as they are taken.
- 6
Log fuel and check pay
Fuel goes in with a receipt photo for IFTA. The pay tab shows an estimate per load, and a pay question can be raised from there.
Phone calls and paper vs. the Tezify driver app
| Question | Calls, texts and paper | Tezify driver app |
|---|---|---|
| Where the next stop is | A call to dispatch | On the load, with directions |
| Proof of delivery | A photo texted to someone, or paper mailed in | Photographed in the app and filed on the load |
| Pre-trip inspection | A paper DVIR book in the cab | In the app, with photos and a signature |
| A question about pay | A phone call that nobody writes down | A pay question on record, answered in the app |
| What the driver sees of your rates | Whatever is on the broker's rate con | A rate con at the carrier rate you set, never the broker's |
| Cost per driver | Nothing, but nothing gets tracked | Included, for every driver |
Common questions
Can a driver see what the load pays the carrier?
- No. The driver sees a rate confirmation generated at the carrier rate you set for them, never the broker's original rate confirmation, and only for loads assigned to them.
What happens if a driver uploads an unreadable proof of delivery?
- Nothing rejects the photo. With AI turned on, a page that looks altered or completely unreadable is flagged to the safety feed so the office can ask for a retake, and the driver can redo the photo from the app.
Does the app track where the driver is?
- Truck positions come from the ELD connected to Tezify. In the app, the driver sets their own duty status.
Does the driver app cost extra per driver?
- No. The app is part of every plan and every driver gets it. You pay by fleet size, not by driver or by login.
What happens if the driver has no signal?
- The app needs a connection to send. If a submit fails in a dead zone, the driver taps it again once there is signal, and the same inspection is not logged twice.
Where to go next
- Trucking software for US carriers and brokers
The whole product on one page, with the price.
- Tezify pricing by fleet size
From $49 a month for 1 truck. No per-seat charges.
- TMS for own trucks, brokered freight or both
How an own-truck load and a brokered load are costed and settled.
- Trucking dispatch software
The load board, rate con auto-fill and the checks before a truck is assigned.
- Freight broker software
Quote, cover, rate con e-sign, track, bill and pay the carrier.
- Transportation management software for carriers
The five jobs a TMS has to do, and what to check before you buy one.
- TMS for small trucking fleets
Getting a 3 to 25 truck fleet onto one system in a week.
See it on your own loads
Run your real loads through it before you decide anything.
- Free trial
- 30 days on up to 2 trucks, card needed
- After that
- From $49 a month, never per seat
- Included
- Every module, on every plan