Freight brokerage TMS · Covering loads

Carrier vetting by MC or DOT number: what Tezify checks

Type the MC or DOT on Carrier Vetting or in the call box. Tezify reads FMCSA's public records live: authority, how long it has been active, insurance filings, out-of-service orders and, with a free FMCSA webKey, the safety rating. Red flags block, amber flags warn.

Updated Open this in Tezify

Why vet every carrier

When a load goes wrong, the shipper looks to you. A carrier with lapsed authority, no liability cover or an active out-of-service order is a claim you pay yourself. Vetting is the check you run before the carrier touches the freight, not after.

Where the data comes from

Tezify reads the files FMCSA publishes: the company census, authority history, active and pending insurance filings, and out-of-service orders. Each source has its own short timeout, so one slow file does not hold up the card. If you save the free QCMobile webKey in Integrations, it also reads the safety rating and whether the carrier is allowed to operate.

What is checked

CheckRedAmber
AuthorityNo active common or contract authority, broker authority only, revocation pendingUSDOT inactive in the census
Authority ageUnder 90 days90 to 180 days
BIPD liabilityNone on file, below required, or cancelled before this load deliversCancellation within 30 days, or only a pending policy
Out of serviceActive order
Safety ratingUnsatisfactory, or not allowed to operateConditional
RecordsMCS-150 older than 2 years, FMCSA mail undeliverable

If a source does not answer, the card says that part could not be checked. Unknown is never shown as clean.

How to vet a carrier

  1. On Carrier Vetting, press Vet a carrier and type the MC or DOT. On a live call, use the call box on the Desk instead.
  2. Read every flag. Press Open SAFER to see FMCSA's own page.
  3. Send the onboarding packet so the carrier can send their W-9, certificate and signed agreement.
  4. Approve once the packet is complete. The carrier then shows as Active.

Carrier management after the first check

Each carrier on your list has a stage: Prospect, Onboarding, In review, Active, Inactive or Do not use. Approval goes through the packet rules you set. A carrier is approved only when every required item is done, or the owner overrides with a written reason that is kept on the packet.

What FMCSA does not tell you

  • A filing is the insurer's notice of the federal minimum. It is not a certificate naming you as holder.
  • Cargo limits, reefer breakdown cover and exclusions are not in FMCSA data. Get the certificate, or check RMIS when it is connected.
  • Whether the person calling really works for that carrier. That is the identity check in the packet.

Common mistakes

  • Trusting a clean card from months ago. Look the number up again on the day you cover.
  • Reading green authority as insured. Check the BIPD line and the certificate too.
  • Approving with the packet half done. Use the owner override only with a reason you can defend later.

Common questions

Do red flags always stop a cover?

Yes, unless the owner overrides with a written reason. Amber flags only warn, so read them before you send the rate con.

Why is the safety rating blank?

The rating comes from FMCSA QCMobile. Save the free webKey in Integrations and the card shows it.

How fresh is the data?

Each number is read live when you look it up and kept for 10 minutes. The card shows when it was read.

Can I vet Canadian or Mexican carriers?

Yes. Set the carrier's country and the packet asks for a W-8BEN-E in place of the W-9, plus a check of the provincial or Mexican authority paper, which you tick by hand.

Ready to do it? This lives at /admin/carriers in Tezify.

Open this in Tezify

Still stuck?

Inside Tezify, press the ? at the top of any page to file a ticket with that page attached. Not a customer yet? Ask us anything.