Freight class calculator

Put in the size and weight of each piece. You get the density in pounds per cubic foot and the LTL freight class that density falls in on the 2025 NMFC scale.

Dimension unitSize in
Weight unitWeight in
Your freight

Density-based class

100

Density

9.38 lb/ft³

Total

53.33 ft³

500 lb

Density-based guidance only. If your commodity has its own NMFC item, that item sets the class.

How freight class works

LTL carriers price freight by class. A low class means dense freight that is easy to stack and cheap to move per pound. A high class means light, bulky freight that takes up trailer space for its weight, so it costs more per pound.

Density is the biggest input. Since July 19, 2025, the National Motor Freight Classification puts many commodities on a single 13-step density scale. Freight that has special handling, stowing or liability concerns can still have its own NMFC item and a different class. This page gives you the density answer. Check the NMFC item for your commodity before you put a class on the bill of lading.

The density scale

NMFC Docket 2025-1 density scale, effective July 19, 2025: density in pounds per cubic foot and the class it gets
Density (lb per ft³)Class
under 1400
1 to under 2300
2 to under 4250
4 to under 6175
6 to under 8125
8 to under 10100
10 to under 1292.5
12 to under 1585
15 to under 22.570
22.5 to under 3065
30 to under 3560
35 to under 5055
50 or more50

Source: NMFC Docket 2025-1 density scale, effective July 19, 2025, as published by LTL carriers.

Worked example

One standard pallet, 48 by 40 inches, stacked 48 inches high, weighing 500 pounds with the pallet.

  1. 48 × 40 × 48 = 92,160 cubic inches.
  2. 92,160 ÷ 1,728 = 53.33 cubic feet.
  3. 500 ÷ 53.33 = 9.38 pounds per cubic foot.
  4. 9.38 is in the 8 to under 10 band, so the density class is 100.

Stack the same 500 pounds only 24 inches high and the cube halves to 26.67 cubic feet. Density doubles to 18.75 and the class drops to 70. Tighter packing is often the cheapest way to cut an LTL bill.

Tips that save a reclass

  • Measure at the widest point, including overhang and the pallet.
  • Round each measurement up to the next whole inch.
  • Do not stack a pallet that cannot take weight on top. Non-stackable freight may be rated on more space than it fills.
  • Keep the scale ticket. If a carrier reweighs and reclasses, it is your evidence.

How Tezify does this for you

Brokers using Tezify enter LTL lines once on the quote. Tezify works out cube, density and an estimated class for each line, and you can override the class when the NMFC item says otherwise.
See the brokerage TMS

Common questions

How do I calculate freight density?

Multiply length, width and height in inches to get cubic inches, then divide by 1,728 to get cubic feet. Divide the weight in pounds by the cubic feet. The result is pounds per cubic foot, and that number picks the class.

Is this the official NMFC class?

No. It is the class the 2025 density scale gives for that density. Many commodities are classed on density alone, but some have their own NMFC item with a different class. The NMFC item for your commodity, and the carrier's inspection, decide the class on the bill.

What changed with the 2025 NMFC update?

NMFC Docket 2025-1 took effect on July 19, 2025. It moved many commodities onto one 13-step density scale, from class 400 for freight under 1 lb per cubic foot down to class 50 for 50 lb per cubic foot or more.

Should I measure the pallet too?

Yes. Measure the shipping unit as it will travel, pallet and packaging included, at its longest, widest and highest points. Weigh it the same way. Measuring only the product makes the freight look denser than it is.

How are several pieces on one shipment handled?

The calculator shows a class for each line and for the whole shipment, using the combined weight over the combined cube. If the lines are different commodities, each one is classed on its own.